To Remove:
1.Before servicing the vehicle refer to the precautions in the repair manual
2.Disconnect negative battery cable
3.Raise and support the vehicle
4.Drain the engine oil into a suitable container
5.Drain the cooling system into a suitable container
6.Lower the vehicle to the ground
7.Move engine hood to assembly position
NOTE: The following work must be carried out with a second person assisting.
Instructions apply to left and right sides.
8.Gently raise retaining clip and simultaneously push upwards
9.Hold engine hood and unhook damper on hood
10.Slide special service tool 51 2 160 or equivalent over damper
11.Open engine hood completely and reconnect damper with special service tool 51 2 160 or equivalent to hood
12.Remove microfilter
13.Open cable duct on lower section of microfilter housing and feed out cable(s)
14.Release screws and remove lower section of microfilter housing
15.Unscrew and remove splash guard
16.Raise and support the vehicle
17.Remove transmission
18.Lower the vehicle to the ground
19.Remove A/C compressor drive belt
20.Remove A/C compressor from bearing block and tie back to one side
NOTE: Do not disconnect A/C lines.
NOTE: The water drain plug is located on the exhaust side of the engine block by cylinder No. 2.
21.Pull locks and disconnect water hoses
22.Remove radiator
23.Remove cover from fuel injectors
24.Remove both oxygen monitor sensors
25.Remove intake air manifold
26.Disconnect water hoses from water pipe and from heating valve
27.Unfasten engine section of wiring harness and place to one side with cable duct
28.Unfasten reservoir for power steering unit and tie up to one side
NOTE: Do not remove the lines.
29.Remove fan clutch with fan impeller from water pump
30.Remove alternator drive belt
31.Remove power steering pump and tie back to one side
32.Suspend engine from special service tool 11 0 000 or equivalent
33.Disconnect right side ground wire
34.Unbolt left and right engine mounts
35.Carefully lift out engine
Top:
To Remove:
1.Before servicing the vehicle refer to the precautions in the repair manual
2.Disconnect negative battery cable
3.Raise and support the vehicle
4.Drain the engine oil into a suitable container
5.Drain the cooling system into a suitable container
6.Lower the vehicle to the ground
7.Move engine hood to assembly position
NOTE: The following work must be carried out with a second person assisting.
Instructions apply to left and right sides.
8.Gently raise retaining clip and simultaneously push upwards
9.Hold engine hood and unhook damper on hood
10.Slide special service tool 51 2 160 or equivalent over damper
11.Open engine hood completely and reconnect damper with special service tool 51 2 160 or equivalent to hood
12.Remove microfilter
13.Open cable duct on lower section of microfilter housing and feed out cable(s)
14.Release screws and remove lower section of microfilter housing
15.Unscrew and remove splash guard
16.Raise and support the vehicle
17.Remove transmission
18.Lower the vehicle to the ground
19.Remove A/C compressor drive belt
20.Remove A/C compressor from bearing block and tie back to one side
NOTE: Do not disconnect A/C lines.
NOTE: The water drain plug is located on the exhaust side of the engine block by cylinder No. 2.
21.Pull locks and disconnect water hoses
22.Remove radiator
23.Remove cover from fuel injectors
24.Remove both oxygen monitor sensors
25.Remove intake air manifold
26.Disconnect water hoses from water pipe and from heating valve
27.Unfasten engine section of wiring harness and place to one side with cable duct
28.Unfasten reservoir for power steering unit and tie up to one side
NOTE: Do not remove the lines.
29.Remove fan clutch with fan impeller from water pump
30.Remove alternator drive belt
31.Remove power steering pump and tie back to one side
32.Suspend engine from special service tool 11 0 000 or equivalent
33.Disconnect right side ground wire
34.Unbolt left and right engine mounts
35.Carefully lift out engine
Comments are closed.